| |
| DDP
Belt Press (3 Belt Unit)
|
|
The DDP is a high quality,
easily maintained belt press designed for the under 1.5 MGD
Waste Water Treatment Plant.
Features:
- Independent
Gravity Belt
- Upflow
solids feedbox
- Curved
wedge zone that applies pressure to the cake throughout
the zone
- Vertical
pressure zone eliminates filtrate pooling/rewetting
- Entire
belt press at operator level.
No platforms are required
- Low
energy requirement
- Very
low maintenance requirements
- Complete
stainless steel frame
- Easy
operation with high reliability
|
|
DDP Applications: Municipal
|
|
|
The Model 3012 DSP Screw Press
is the ideal choice for the plant with a low wash water
requirement and/or the necessity to dewater material that
may contain tramp material.
Features:
- Independent pre-thickening
with rotary drum thickener (RDT) for enhanced capacity and
cake solids.
- Slot screen design prevents
plugging, maximizes capacity.
- Filtrate recycle
significantly improves solids capture.
- Replaceable flight lowers
maintenance costs.
- Tapered screw design
provides ighest cake solids in the industry.
- Pressure plate is easily
adjustable.
|
|
 |
|
|
The Gravity Belt Thickener is
used to thicken sludge prior to centrifuge or digestion
processes. A mix of primary or secondary sludge can
easily be thickened to +7% wt, pure secondary to over 5%.
Features:
- High unit capacity per floor
space
- Low residence time
eliminates
septicity and float scum
- Superior thickening
- Low maintenance, easy
operation, reliable
|
|
GBT Applications: Municipal,
Industrial, P&P
|
|
|
|
The Rotary Concentrator is an alternative to the GBT for thickening
that requires less floor space and less operator attention.
Features:
- Lower cost
- Simpler operation;
no belt tracking or tensioning
- Smaller floor space
|
|
Rotary
Concentrator Applications: Industrial
|
|
|
The belt press has been the
equipment of choice for municipal sludge dewatering since its
inception in the early 1970's. The Model 3DP has
features offered by no other manufacturer.
Features:
- Paddle wheel feed box that
provides very uniform slurry distribution with no
clogging.
- Independent filter belt in
gravity zone
- Curved wedge zone that puts
pressure on cake through the entire zone.
- Vertical pressure zone
eliminates filtrate pooling/rewetting
- Observe gravity zone without
platform
- Very high discharge cake
solids
- Low energy requirement
- Low maintenance, easy
operation, reliable
- Tubular steel hot dipped
galvanized frame that is easy to keep clean.
|
|
3DP
Applications: Municipal,
Industrial
|
|
All
the same features as the model 3DP except there is no
Independent Gravity Zone. The gravity zone is driven
by the press section similar to most belt press
designs.
|
|
2VP
Applications: Municipal,
Industrial
|
|
|
|
Features:
- Paddle wheel assisted high
feed solids feed box for even distribution with high
viscosity feed slurries.
- All
rolls vulcanized rubber covered for abrasion resistance
- Rugged
/ Heavy duty construction for Sevier Minerals service
- Feed
Box and Gravity Zone at operator level, no need for
platforms
- Very thick slide strips to
provide long wear life.
Replaceable from side by simply sliding new strip on.
- Open
frame design for maintenance access
- Heavy
duty bearing / journal size
- Decreasing roll diameter - pressure
zone to produce higher cake pressures.
|
|
Sahara
Applications: Mineral
|
|
|
Models HO3x3 and HO2x3 were
developed specifically for the paper industry to maximize cake
consolidation. Both models can discharge cake solids to
over 50%.
Features:
- Independent gravity zone
- 50 pli "S" Roll
section
- 150 pli Nip Roll section
- Synchronized independent
drives
- Very high discharge cake
solids
- Extremely heavy, rugged
design
- Low maintenance
|
|
HO3x3
Applications: Pulp & Paper
|
|
|
Features:
- Features similar to HO3x3 in
a 2-belt design
- Cost is less than that of
the HO3x3
|
|
HO2x3
Applications: Pulp & Paper
|
|
|
|
|
|
|
